Hydro Jetting Melbourne | Blocked Drains Cleared
Plumbers Available Now
Drainpro

Drainpro - Drain Specialists Since 1999

Hydro Jetting Melbourne Power Cleared

High-pressure hydro jetting blasts through grease, sludge and tree roots.

1,300+ Reviews Since 1999 Fixed Pricing
Call 1300 303 247
Fast local response

Enquire Now

We only call about your enquiry. No spam.

1,300+ reviews · Same-day response

1,300+ Reviews

25+ Years

Fixed Pricing

130+ Suburbs

High-pressure water jetting that actually cleans the pipe

A blocked drain usually doesn’t need a new pipe. It needs the inside of the pipe cleaned properly, and that’s the job hydro jetting does. We feed a high-pressure hose into the line and work it through. The water jets on the nozzle strip grease, silt, roots and scale off the pipe wall as the head travels.

It’s the difference between clearing a drain and cleaning it. You’ll see the before and after on camera during the same visit.

Call 1300 303 247 for same-day service.

What hydro jetting actually does

A jetter is a hose on a reel with a nozzle on the end. It’s fed into your drain through a pit, a gully or a fixture. Water leaves the nozzle through jets angled backwards, which drives the head forward. The front of the nozzle cuts into whatever is ahead of it.

The water hits the pipe wall on the way through, and that’s where the job gets done. It’s not shoving the blockage downstream. It’s washing away the surface the blockage was clinging to.

How it differs from a plunger or a drain snake

A plunger shifts water and air to move a soft blockage in a short section. A drain snake, or eel, is a steel cable with a cutting head that drills through the middle of the blockage so water can pass. Both leave the pipe walls coated in whatever caused the problem in the first place. A jetter cleans the walls, so grease and silt take much longer to rebuild.

If your drain blocks every few months, that’s the loop a snake can’t break.

Pressure and nozzles in plain terms

Pressure gets turned up or down to suit the pipe. Old terracotta and thin PVC get less, heavy concrete stormwater lines can take more. The nozzle matters as much as the pressure.

A penetrating nozzle with a forward jet breaks through a solid blockage first so the hose can keep moving. A flushing nozzle spreads a wider curtain of water for silt and sludge. A root nozzle cuts growth away from the wall.

We change nozzles mid-job when the camera says we should.

Blockages jetting handles well

Most of the calls we get fall into a few groups:

  • Grease and fat in kitchen and laundry lines, which sets hard as it cools
  • Silt, mud and sand washed into stormwater drains after heavy rain
  • Fine tree roots that have grown through a joint and spread inside the pipe
  • Scale and mineral build-up in older lines, which narrows the pipe over years
  • Wet wipes and paper that snag on a rough wall

None of these need a new pipe. They need the pipe cleaned back to a smooth wall.

Roots: what a jetter can cut and what it can’t

A jetter deals with fine roots, the growth that fills a pipe once a root finds a cracked joint. It cuts them out and washes them away. A thick root mass, or a root that has pushed the pipe apart, needs a mechanical cutter first. We camera it afterwards to see what’s left.

If the joint has opened far enough for roots to get in, jetting clears it this time and the roots return. That’s a repair question, not a cleaning question.

Why we put a camera in first

Jetting blind is how pipes get damaged. If the line has already collapsed, or a section has dropped and bellied, pushing a high-pressure hose into it can make things worse. A camera shows the pipe material, the size, where the blockage sits and what it’s made of.

On a blocked drain call the inspection is included at no charge, and you watch the screen as we go. If we find something jetting shouldn’t touch, we stop and explain it.

Commercial kitchens and strata buildings

Grease is the main problem in any kitchen that cooks with oil. It cools in the line, sets on the walls and narrows the pipe until a busy service backs up. Restaurants, cafes, bakeries and food courts usually want the work done outside opening hours, and we plan the visit around that.

Strata buildings bring their own complications. Shared lines, body corporate approval, and nobody quite certain which pipe belongs to whom. We inspect the whole run and put the findings in writing so the committee can decide.

What happens on site

We start at the access point closest to the problem and check the flow. The camera goes in first and we find the blockage. Then we set up the jetter, feed the hose in and work it through the line in stages. We pull back slowly so the water has time to cut.

We check with the camera again, run a second pass if the pipe needs it, and show you the footage. Then we clean up and leave the pit or gully as we found it.

Maintenance jetting

If your line blocks once, jetting fixes it. If it blocks twice in a year, something is wrong with the pipe and cleaning is only buying time. For lines that carry a lot of grease, or sit under established trees, a scheduled jet keeps the pipe clear and saves the emergency call. We’ll tell you what interval suits your property based on what the camera shows, not on a sales script.

Some lines want a yearly clean. Plenty don’t need one at all.

When hydro jetting is not the right job for you

Jetting cleans pipes. It doesn’t repair them. If the camera shows a collapsed section, a displaced joint or a pipe cracked through, water won’t fix any of it.

Neither will it fix a line that’s sagged into a belly, and pressure can make both worse. Same story if there’s no access point, or the only access is through a fixture we can’t protect. Those jobs belong with drain repair, pipe relining or drain replacement.

We’ll say which and why before anything is booked.

What it costs and how we quote

Call-out starts at $45. After that we quote the job once we’ve seen the pipe on camera. The price depends on length, access and what’s actually in the line. You get the figure before we start, and it doesn’t move because the job took longer than expected.

We don’t run a meter. If the honest answer is that the pipe needs replacing rather than cleaning, you’ll hear that instead of a cleaning quote. That’s the whole pricing story.

Why Melbourne properties call us

Drainpro has worked on Melbourne drains since 1999, from depots in Oakleigh, Essendon and Ivanhoe, and we cover 130 suburbs across the city. We’re a Master Plumbers member (504231) and hold BPC licence 43464. Weekday hours run 6:30am to 7pm, Saturday 7am to 5pm, Sunday 8am to 4pm, and emergency calls are answered around the clock. Our blocked drains service handles the urgent calls, and a CCTV inspection is where most jetting jobs begin.

Frequently Asked Questions

How much does hydro jetting cost in Melbourne?

Call-out starts at $45, then we quote a fixed price after the camera has been through the line. Length, access and the severity of the blockage all affect it. You get the number before we start work.

Is hydro jetting safe for old terracotta pipes?

Yes, when the operator checks the pipe first. Terracotta gets lower pressure than newer PVC or concrete, and we watch the walls on camera as we go. If the pipe is fragile or already failing, we’ll say so and recommend something else.

Can hydro jetting clear tree roots?

It clears fine root growth inside the pipe and washes it away. Heavy root masses need a mechanical cutter first, then jetting to finish the clean. If roots got in through a failed joint, the joint still needs repairing or relining to keep them out.

Will jetting damage my pipes?

Not when the pressure and nozzle match the pipe, which is why the camera goes in first. The real risk is jetting a line that’s already collapsed or badly sagged. That’s the sort of thing we check before the hose goes anywhere.

Do you need access inside the house?

Usually not. Most lines can be jetted from an outside pit, gully or inspection opening. No worries if the only access is through a fixture. We’ll protect it and explain what we’re doing before we start.

How often should a commercial kitchen be jetted?

It depends on how much oil goes down the drain and how the line is built. Kitchens that fry heavily tend to need it more often than those that don’t. We’ll recommend an interval after seeing the pipe, and put it in writing rather than guess at it.

Can hydro jetting fix a collapsed drain?

No. Jetting cleans a pipe that still has its shape and structure. A collapsed section has to be dug out and replaced, or relined where the damage allows it. We’ll show you the footage so you can see why.

How long does a jetting job take?

Most residential blockages are cleared in a single visit, with camera before and after. Commercial and strata lines can take longer because there’s more pipe to work through. We’ll give you a realistic idea once we’ve seen the access and the blockage.

Get a quote

Give us a call on 1300 303 247. We’ll get a camera into the line, show you what’s going on and quote the clean before we start. Same-day service is often available, and emergency calls are answered 24/7.

Learn more

Suburbs we service

Hydro Jetting across Melbourne, including Oakleigh, Northcote, Fairfield, Thornbury, Preston, Highett, Hampton, Hughesdale, Cheltenham, Murrumbeena, Essendon, Doncaster, Kew, Mount Waverley.

See all suburbs we cover

Frequently Asked Questions

How much does hydro jetting cost in Melbourne?

Call-out starts at $45, then we quote a fixed price after the camera has been through the line. Length, access and the severity of the blockage all affect it. You get the number before we start work.

Is hydro jetting safe for old terracotta pipes?

Yes, when the operator checks the pipe first. Terracotta gets lower pressure than newer PVC or concrete, and we watch the walls on camera as we go. If the pipe is fragile or already failing, we'll say so and recommend something else.

Can hydro jetting clear tree roots?

It clears fine root growth inside the pipe and washes it away. Heavy root masses need a mechanical cutter first, then jetting to finish the clean. If roots got in through a failed joint, the joint still needs repairing or relining to keep them out.

Will jetting damage my pipes?

Not when the pressure and nozzle match the pipe, which is why the camera goes in first. The real risk is jetting a line that's already collapsed or badly sagged. That's the sort of thing we check before the hose goes anywhere.

Do you need access inside the house?

Usually not. Most lines can be jetted from an outside pit, gully or inspection opening. No worries if the only access is through a fixture. We'll protect it and explain what we're doing before we start.

How often should a commercial kitchen be jetted?

It depends on how much oil goes down the drain and how the line is built. Kitchens that fry heavily tend to need it more often than those that don't. We'll recommend an interval after seeing the pipe, and put it in writing rather than guess at it.

Can hydro jetting fix a collapsed drain?

No. Jetting cleans a pipe that still has its shape and structure. A collapsed section has to be dug out and replaced, or relined where the damage allows it. We'll show you the footage so you can see why.

How long does a jetting job take?

Most residential blockages are cleared in a single visit, with camera before and after. Commercial and strata lines can take longer because there's more pipe to work through. We'll give you a realistic idea once we've seen the access and the blockage.

Our Recent Work

Hydro Jetting Melbourne

Need Hydro Jetting Melbourne?

Call 1300 303 247 for same-day service across Melbourne. Fixed pricing, no surprises.

Fixed pricing 1,300+ reviews Workmanship guaranteed
Call 1300 303 247
Call Now Book Now